Toyota Automobile Accessories TY 71 00 G3 User Manual

Page 1 of 3

TOYOTA TUNDRA 2000-2006

TOYOTA SEQUOIA 2001-2007

(MANUAL CLIMATE CONTROL ONLY)

See page 2 for Automatic Climate Control

PART NUMBER: TY-71-00-G3

PLEASE READ COMPLETE INSTRUCTIONS BEFORE INSTALLING THIS VSM G3

All instructions assume a drivers seat vantage point. Caution is advised when removing and reassembling

wood or plastic parts of a dash. Applying unnecessary force or pressure may cause a piece to crack or break.

When properly installed, the metal between the ball and 2 small holes is all that is exposed.

(Some exceptions apply).

#2 Phillips screwdriver, hook tools, 5/64” drill bit and drill, marking pen.

VSM G3, A Plate, J Stem, two (2) #8 1/2” screws

Right of air vent

TOOLS REQUIRED:

PARTS INCLUDED:

LOCATION:

STEP 1. Locate the two air vents that are on the right and left

sides of the radio. Remove both of these air vents by inserting

the hook tool between the vents and the bezel and carefully

prying outward on the vents to remove. Set the vents aside.

Inside the vent cavities locate and remove two (2) Phillips

screws using the Phillips screwdriver. Set the screws aside.

STEP 2. Locate the three knobs that are on the climate

control. Grasp the knobs and carefully pull toward you to

remove. Set the knobs aside. Locate and remove the three(3)

Phillips screws that are behind the knobs. Set the screws

aside. Grasp the top middle section of the bezel just above

the radio and carefully pull towards you releasing the top clip.

Insert both your hands into the air vent cavities. Grasp the

bezel and pull toward you to release a series of six clips that

are behind and attached to the back of the climate control.

These clips hold the lower section of the bezel in place. When

the bezel is loose do not disconnect any wiring. Let the bezel

hang.

STEP 3. Locate the flat section of plastic to the right of the

right air vent. Place the VSM G3 over this section of plastic,

making sure that the bottom of the G3 is level. Once the G3 is

in position, mark two (2) spots for drilling pilot holes using the

two (2) holes in the G3 as a guide. Set the mount aside.

Carefully drill two (2) pilot holes using the 5/64” drill bit and

drill, making sure to not drill too deep. Place the VSM G3 over

the two pilot holes. Insert the two (2) #8 x 1/2” provided

screws and tighten.

STEP 4. Re-assemble the dash in reverse order. This completes

the installation of your VSM G3.

Note: See the Assembly Instructions for G3 Components for

additional information.

Pro.Fit International, Inc.® may not be held liable for any damage to a vehicle before, during or after the installation or removal of this VSM

G3. Pro.Fit International may not be held liable for any personal injury resulting from accident or improper installation. Pro.Fit International,

Inc.® 1335 Eagandale Court, Eagan, MN 55121, Ph: 651.688.3588 or 800.388.0073 Fx: 651.688.9876

View Instruction & Updates

Online at

www.pro-fit-intl.com

Page 3 of 3

Mercury Mountaineer 2006-2008

Ford Explorer 2006-2009

Ford Sport Trac 2008

TY-71-00-G3

PLEASE READ COMPLETE INSTRUCTIONS BEFORE INSTALLING THIS VSM G3

All instructions assume a drivers seat vantage point. Caution is advised when removing and reassembling

wood or plastic parts of a dash. Applying unnecessary force or pressure may cause a piece to crack or break.

When properly installed, the metal between the ball and 2 small holes is all that is exposed.

(Some exceptions apply).

TOOLS REQUIRED: #2 Phillips screwdriver, Dash Trim Tool (DTRT) 5/64” drill bit and drill, 7mm socket and driver

marking pen.

PARTS INCLUDED: VSM G3, A Plate, J Stem, two (2) #8 1/2” screws

LOCATION: Right of Radio

STEP 1. Apply parking brake and place gear shift into drive. Open

center arm rest and remove two (2) 7mm bolts from the front of the

console. Photo #1. Insert DTRT behind the gear shift trim bezel.

Press down to release a retainer clip. Work the tool around the trim

until all clips are released. Lift ring over gear shift and set aside.

7mm

STEP 2. Insert the DTRT behind the cup holder/shifter bezel near

the 7mm bolt holes. Press down to release a clip. Work the tool

around the bezel until all clips are free. Lift bezel over shifter,

disconnect wiring and set bezel aside. Photo #1.

STEP 3. Insert DTRT behind the upper-right corner of the radio

bezel. Press down gently to release a clip. Work the tool around

the bezel until it is completely free. Very carefully disconnect the

wiring and vacuum lines from the bezel. Set bezel aside.

STEP 4. Remove four (4) screws from the corners of the radio. Pull

radio out of its cavity, wrap protective cloth around radio and let it

hang down. DO NOT disconnect radio wiring.

STEP 5. Place the VSM G3 against the right side of the radio cavity,

aligning it just above the clip hole. Photo #2. Using the VSM G3 as a

guide, mark the location of the two (2) screw holes and set the VSM

G3 aside. Use a utility knife and trim the small ridge behind the VSM

G3 so it sits tight against the dash pad. Drill two (2) pilot holes at

the marked locations using a 5/64” bit and drill. Align the VSM G3

over the pilot holes, insert two (2) #8 x 1/2” screws and tighten.

Clip

Hole

STEP 6. Assemble the dash in reverse order, remembering to

reconnect the wiring harness. You have successfully installed your

VSM G3.